耐酸堿防腐塗料

Product Categories

hot key words

contact us

Zibo ShiNaite anti - corrosion Technology Co., Ltd

Contact: Wang Zhong

mobiles: 17663023308 15589303703

E-mail: chinashinaite@163.com

Fax: 0533-7070433

Address: Zibo City, Shandong Province Linzi District Qilu International Plastic City fine plasticized area 11-1

Website: www.ssttme.com.cn

SNT-921 wear-resistant brush ceramic

Your current locations: Home >> Products >> Wear-resistant coating

SNT-921 wear-resistant brush ceramic

  • category:Wear-resistant coating

  • The number of clicks:
  • Release date:2017/09/27
  • Online inquiry
Details

SNT-921 wear-resistant brush ceramic is imported high-performance epoxy resin with special curing agent and modified additives, adding high-performance filler (alumina, silicon carbide, etc.) made of. Two-component, color adjustable; high strength, good toughness, wear resistance, corrosion resistance, anti-aging; room temperature curing. Widely used in equipment corrosion and repair and protection.

LT466 wear-resistant anti-corrosion ceramic coating performance parameters

project

index

Detection method

Appearance, viscosity

A component

Viscous liquid
(220000)

Visual inspection

B component

liquid(600)

Visual inspection

density(g/cm3)

A component

1.60-1.70

GB/13354

B component

1.0-1.1

GB/13354

Adjust the proportion of plastic

A:B=6:1(weight ratio)


Operating time(min/25℃)

25-35

GB/T7123

Hardness (Shore D)

86

GB/T2411

Shear strength(Mpa)

23

GB/T7124

Compressive strength(Mpa)

115

GB/T1041

Tensile Strength(Mpa)

32

GB/T6329

Smoke resistance time(h)

5000

GB/T6329

100%load curing time(25℃)

Curing at room temperature 24h

——

Operating temperature(℃)

-60~120

——


SNT-921 wear-resistant brush ceramic applications

  1, the general industry: cooling tower wind blades, decorative slope, equipment, easy to wear parts, pump shell and leaves, the valve inside and outside.

  2, the ship industry: pressure warehouse, oil tank, drinking water tank, hull shell, hull underwater surface, rudder, cabin and water propeller inlet and outlet.

  3, the energy industry: turbine blades, dam gates, blower films, waste shelves.

  4, offshore oil industry: easy wet well, easy to wear deck, equipment surface, sliding surface, helicopter airport, underwater wells, lifting pipes and lifting pipe outer tube.

  5, oil and petrochemical industry: rotating machine, loading and unloading surface, pump casing and leaves, valves, piping systems.

  6, the traffic industry: the bridge is easy to wet or underwater parts, transport salt, asphalt and fertilizer towing inside the trunk.

  7, pulp and paper industry: equipment easy to wear parts.

  SNT-921 wear-resistant brush ceramic use:

  1, surface treatment: (1) clean up the surface impurities. (2) Rough the surface to be repaired to increase the surface adhesion. (3) cleaning agent cleaning and drying dry.

  2, with plastic: according to the provisions of the proportion of the appropriate mix in the container evenly, (constantly scraping the side of the container and the bottom of the mixture), until no lines, the same color until.

  3, coating: the mixed even SNT-921 on the substrate surface twice or more brushing, each layer thickness of about 0.5mm to reduce the pinhole or leakage brush. (Spraying, according to the needs of the scene to add 15% to 25% of the thinner).

  4, curing: room temperature (15 ℃ to 28 ℃), 24h fully cured. Temperature below 10 ℃, the curing speed is slow, should take appropriate measures to promote curing curing. Temperature is higher than 30 ℃, for a short time, should reduce the operating time or reduce the amount of plastic.

Precautions

  This product is non-dangerous goods, according to general chemical transport. Store in a cool and ventilated place, avoid contact with skin and eyes. Shelf life of 1 year.


Related tags:Wear-resistantprotectivecoating,SNT-921wear-resistantbrushceramic價格,SNT-921wear-resistantbrushceramic批發

Previous:None
Next:None

Recently Viewed:

S
E
R
V
E
R
share